DAS Audio

 














Previous Page

DR 115A

Two-Way Powered Full Range Speaker

DR 115A
DR 115A Speaker

list price: $874
our price: $700


The DR-115A exemplifies the achievements of D.A.S. engineers in high pressure injection molding technology. The DR-115 mounts a proprietary 15 in. low frequency transducer and the high efficiency M-34 compression driver and CD horn assembly.

The DR-115A incorporates the latest in amplifier technology. A Class "D" amplifier powers the low frequency section and a Class "A/B" powers the highs. Protection circuitry is provided for both amps and the components.

View DR Series
DR 115A Features:
  • Biamplified 2-way vented loudspeaker system
  • 15 in. Neodymium cone speaker
  • 1 in. Neodymium compression driver
  • 300 W + 100 W power amplifier
  • Polypropylene enclosure
DR 115A Accessories:

ANL-1
ANL-1

Rigging Kit With 4 Eyebolts + 4 Carabiners.

$35


FUN-DR-115
FUN-DR-115

Protective transport cover for 1 DR-115/DR-115A.

$117


AX-115
AX-115

Adjustable wall mount.

$102




TRD-2


TRD-2

Speaker stand for 35 mm pole mount sockets.

$146




TRD-4


TRD-4

Pole mount for sub.

$15


DR 115A Replacement Parts:

GM-M-34
GM-M-34

HIGH
Replacement diaphragm for compression drivers.

$50




GM-15MI4


GM-15MI4

LOW
Complete recone kit for cone loudspeakers.

$67




MP-DR-115A


MP-DR-115A

POWER MODULE
Power Module

$914


DR 115A Specifications:

Nominal LF Amplifier Power 300 W
Nominal HF Amplifier Power 100 W
Frequency Range (-10 dB) 45 Hz-20 kHz
Rated Peak SPL at 1 m 130 dB
Dispersion 90°H x 45°V
Enclosure Material Polypropylene
Color/Finish Black
Connectors Input: Female XLR
Loop Thru: Male XLR
AC Input: Male IEC
AC Requirements 115 V, 50 Hz/60 Hz
230 V, 50 Hz/60 Hz
Current Draw (1/3 power @ 230 V) 0.66 A
Dimensions (H x W x D) 28 x 16 x 16.5 in
71 x 46 x 42 cm
Weight 48.5 lbs.
22.1 kg


The 2-way full range powered loudspeaker shall incorporate a 15 inch cone low frequency transducer and a 1 inch throat compression driver mounted to a constant directivity horn. The frame of the low frequency speaker shall be manufactured of die-cast aluminium. The low frequency voice coil shall be 3 inches in diameter. The high frequency voice coil shall be 1.75 inches in diameter and the diaphragm shall be constructed of titanium. All transducers shall use Neodymium magnets.

The system specifications of a typical production unit shall be as follows: On-axis frequency range shall be of 50 Hz to 15 kHz. Coverage angles shall be 100 degrees horizontal and 70 degrees vertical (average of 1/3rd octave bands from 500 to 8 kHz).

The system shall feature a class-D amplifier for the low frequencies and a class-AB amplifier for high frequencies. Nominal power output for the low frequency amplifier shall be 300 WRMS. Nominal power output for the high frequency amplifier shall be 100 WRMS. The amplifiers shall contain protection systems. The built-in active 2-way equalised crossover shall provide 24 dB/octave slopes. The input shall be electronically balanced on an XLR connector, and an output XLR loop through connector shall also be provided. Input shall be switchable between line and microphone. A switchable high-pass filter shall also be provided. AC connection shall be through a detachable IEC cable. Display LEDs shall be provided.

The system’s low frequency driver shall be mounted as direct radiator into a bass-reflex cabinet constructed of polypropylene. The low frequency speaker shall be covered with a perforated steel grille, sealed against corrosion using a polyamide powder coat finish. Two bar handles shall be provided. Nine 8M rigging points shall be provided.

The system shall be a D.A.S. DR-115A.