DR 115
list price: $389 our price: $500
|
The DR-115 exemplifies the achievements of D.A.S. engineers in high pressure injection molding technology. The DR-115 mounts a proprietary 15 in. low frequency transducer and the high efficiency M-34 compression driver and CD horn assembly.
Handles, a tripod mount and rigging points make this cabinet an excellent choice for the road or permanent installation.
View DR Series
| DR 115 Features: |
- Two-way full-range system
- Non-powered and powered versions
- 15 in. speaker with injected molded aluminum chassis
- High frequency compression driver with 2 in. titanium diaphragm
- Floor monitor position
- Standard pole-mount socket for use with tripod
|
DR 115 Accessories:
|

|
ANL-1
Rigging Kit With 4 Eyebolts + 4 Carabiners.
$35
|
 |

|
FUN-DR-115
Protective transport cover for 1 DR-115/DR-115A.
$117
|
 |

|
AX-115
Adjustable wall mount.
$102
|
 |

|
TRD-2
Speaker stand for 35 mm pole mount sockets.
$146
|
 |

|
TRD-4
Pole mount for sub.
$15
|
 |
DR 115 Replacement Parts:
|

|
GM-M-34
HIGH Replacement diaphragm for compression drivers.
$50
|
 |

|
15MI
LOW Complete replacement loudspeaker for low fequency ways.
$67
|
 |

|
GM-15MI
LOW Complete recone kit for cone loudspeakers.
$67
|
 |
DR 115 Specifications:
|
| RMS Power Handling |
350 W |
 |
| Peak Power Handling |
1400 W |
 |
| Frequency Range (-10 dB) |
45 Hz-20 kHz |
 |
| Nominal Impedance |
8 ohms |
 |
| On-axis Sensitivity 1 W / 1 m |
100 dB SPL |
 |
| Rated Peak SPL at 1 m |
131 dB |
 |
| Dispersion |
90°H x 45°V |
 |
| Enclosure Material |
Polypropylene |
 |
| Color/Finish |
Black |
 |
| Connectors |
2 x NL4 Speakon |
 |
| Dimensions (H x W x D) |
28 x 18 x 16.5 in 71 x 46 x 42 cm |
 |
| Weight |
41 lbs. 18.6 kg |
The 2-way passive full range loudspeaker shall incorporate a 15 inch cone low frequency transducer and a 1 inch throat compression driver mounted to a constant directivity horn. The frame of the low frequency speaker shall be manufactured of die-cast aluminium. The low frequency voice coil shall be 3 inches in diameter. The high frequency voice coil shall be 1.75 inches in diameter and the diaphragm shall be constructed of titanium. The magnet for the high frequencies shall be Neodymium.
The system specifications of a typical production unit shall be as follows: Average (RMS) power handling (based on a two hour test using an IEC band-limited 6 dB crest factor pink noise signal) shall be 350W. On-axis frequency range shall be of 50 Hz to 19 kHz. On-axis sensitivity (1W / 1m) shall be 100 dB SPL. Coverage angles shall be 90 degrees horizontal and 60 degrees vertical (average of 1/3rd octave bands from 500 to 8 kHz). Nominal impedance shall be 8 ohms.
The system’s low frequency driver shall be mounted as direct radiator into a bass-reflex cabinet constructed of polypropylene. The low frequency speaker shall be covered with a perforated steel grille, sealed against corrosion using a polyamide powder coat finish. Three bar handles shall be provided. Nine 8M rigging points shall be provided.
The system shall be a D.A.S. DR-115. |
|
|