Anchor Audio


Previous Page

ANX-70 Full-Range Loudspeaker Monitor

Powered Speaker System Engineered to Provide Quality Full-Range Sound Projection in a Variety of Outdoor and Indoor Applications

ANX-70 Full Range Loudspeaker Monitor
ANX-70 Speaker Monitor

starting at: $152


The ANX-70 is a full-range loudspeaker system engineered to provide quality full-range sound projection in a variety of outdoor and indoor applications. Its wide range, enhanced mid range response and high efficiency ensure superb projection of clear intelligible speech. The speaker is supplied with an adjustable mounting bracket allowing for easy wall and ceiling installation. A 70 volt line transformer with three taps provides adjustable wattage setting.
ANX-70 Features:
  • Enhanced Speech Intelligibility
  • Smooth Frequency Response
  • Magnetically Shielded
  • Ease of Mounting With U Bracket
  • Rugged Steel Grille
  • Built-In top Quality 70 Volt Line Transformer with Minimal Saturation
  • 4 in. (100 mm) Woven Carbon Fiber Woofer
  • 5/8 in. (10 mm) PEI Dome Tweeter w/ Ferrofluid for Best Reliability
  • 1/4 in. (6 mm) 8 Ohm Input
  • Push Terminals
  • Made in the USA
ANX-70 Components:

Part No.




ANX-70 70 Volt Unpowered Speaker $152  

SB-1 Stand Mount $59  
SB-3 40° Tilt Bracket $25  
SB-360 360° Swivel $29  
RM-1 Single Rackmount $66  
RM-12 Dual Rackmount $76  
ANX-70 Specifications:

Frequency Range 80 Hz – 20 kHz (-10 dB)
Suggested Amplifier Power See note below *
Nominal Coverage 105° x 105°
Nominal Sensitivity 86 dB SPL , 1W @ 1 m (3.3ft)
Maximum SPL @ 1m 108 dB continuous peak pink noise, 103 dB continuous average
pink noise, 100 dB continuous average music or speech
Crossover Type First Order High-pass
Input Selection 70 volt-line transformer taps @ 5W, 10W, and 30W 1/4 in. (6.0 mm) 8 Ohm
Transducers Low-Frequency – 4 in. (100 mm) woven carbon fiber w/ treated cloth edge surround, 1 in. (25 mm) voice coil on aluminum former, magnetically shielded

High-Frequency – 5/8 in. (10 mm) dome of PEI
Enclosure Material ABS
Grille Painted perforated steel
Mounting Use with SB-1BK Speaker stand bracket, SB-3BK wall mount bracket, SB-360BK swivel wall mount bracket, RM-1BK single rack mount kit, RM-12BK dual rack mount kit.
Dimensions (HWD) 5.25 x 8.375 x 9 in.
13.3 x 21.3 x 22.9 cm
Weight 4.2 lbs.
1.9 Kg
* Multiply the number of speakers on each channel by 30 watts to obtain the optimum amplifier RMS wattage rating.
Example 1: 5 speakers per channel requires an amplifier rated at 150 watts per channel. If some speakers will be set to the 5 or 10 watt taps then the minimum necessary amplifier power will be less.
Example 2: 3 speakers at 30 watts, one speaker at 10 watts and 1 speaker at 5 watts would require an amplifier rated at 105 watts minimum per channel.
Amplifiers rated at significantly more than the minimum calculated power can be safely used so long as their line output is 70 volts. Do not use the ANX-70 on 100 volt line systems. In no case should the system volume be set to a level that produces distortion. Distortion typically occurs when an UNDERPOWERED amplifier is used.